Search found 93 matches
- Wed Aug 12, 2015 5:48 pm
- Forum: Mixcraft
- Topic: Novation Mininova Hook-up
- Replies: 2
- Views: 1314
Novation Mininova Hook-up
Just bought a Novation Mininova. I have it hooked up and it shows in the category dropdown...I select it and it still produces no sound. If I select another synth sound it will act as a midi controller though. Please explain the hook-up. Do I go 1/4 inch into my Audiobox?
- Thu Jul 16, 2015 5:48 pm
- Forum: Mixcraft
- Topic: Output Signal tracks out of sync after mixdown
- Replies: 4
- Views: 1895
Re: Output Signal tracks out of sync after mixdown
Okay... sound device preferences have been at 48000 and I always mix down to wave and it is set at 48000. Still way out of whack. Sounds great within Mixcraft. Mixdown to WAV and put on soundcloud and it's off. This only happens with a "Signal Pulse Engine" track....or a syncopated Omnisph...
- Wed Jul 15, 2015 6:49 am
- Forum: Mixcraft
- Topic: Output Signal tracks out of sync after mixdown
- Replies: 4
- Views: 1895
Output Signal tracks out of sync after mixdown
Whenever I mix down tracks with Output Signal use it is out of sync. Also happens using a syncopated sound out of Omnisphere. I suspect some kind of sample rate issue? Please advise. Thanks
- Tue Jun 02, 2015 11:12 am
- Forum: Mixcraft
- Topic: Installing MIDI loops
- Replies: 6
- Views: 4055
Installing MIDI loops
Feel stupid asking this but how do I install a pack of "MIDI" drum loops. Bought a pack from Loop Loft. I've always uploaded WAV loops fine but that procedure obviously doesn't work for MIDI loops...any help appreciated. Thanks
- Fri May 08, 2015 11:44 am
- Forum: Mixcraft
- Topic: Patches sticking "on" with Omnisphere 2
- Replies: 4
- Views: 3152
Patches sticking "on" with Omnisphere 2
Playing a patch...all of the sudden it sticks and keeps playing a note when key is released. Only way to get it to stop is change the sound, then unplug and replug the usb on the controller. It happened every once in a while with Omnisphere 1 and other synths. But after upgrading to 2 it happens qui...
- Sat Mar 28, 2015 5:03 pm
- Forum: Mixcraft
- Topic: How to get Omnisphere to show up in Mixcraft 7
- Replies: 2
- Views: 2726
How to get Omnisphere to show up in Mixcraft 7
Just bought and loaded it. To register it it says to open in "Host"... don't see it in mixcraft. Saw a post on here similar but the solution made no sense. I don't think this is your typical VST so before I start screwing around I figured I'd ask on here for the correct steps. I'm sitting ...
- Fri Mar 20, 2015 3:41 pm
- Forum: Mixcraft
- Topic: Can't hear Omni Sampler loop
- Replies: 2
- Views: 1590
Re: Can't hear Omni Sampler loop
It was the velocity....why they default to almost nothing doesn't make sense. But thanks
- Wed Mar 18, 2015 4:18 pm
- Forum: Mixcraft
- Topic: Can't hear Omni Sampler loop
- Replies: 2
- Views: 1590
Can't hear Omni Sampler loop
I can hear when I click the yellow play arrow on individual samples....but when I play the loop.....nothing. Clicking the yellow play arrow also registers input on the level meter of the track but when the loop is played there is no level registering.....help
- Fri Feb 27, 2015 7:12 pm
- Forum: Mixcraft
- Topic: MP3 Mixdown always has way too much low end....Help!
- Replies: 17
- Views: 8188
Re: MP3 Mixdown always has way too much low end....Help!
Am I supposed to mixdown to a wav....then bring that wav back into Mixcraft by itself and master from there??
- Fri Feb 27, 2015 7:08 pm
- Forum: Mixcraft
- Topic: MP3 Mixdown always has way too much low end....Help!
- Replies: 17
- Views: 8188
Re: MP3 Mixdown always has way too much low end....Help!
Sorry for the confusion. Yes....changed it in the mixdown to wav to match. Here is a link to the song on soundcloud. https://soundcloud.com/factosound/slow-burn Sounds fine on my studio computer. It's when I listen in the car or another computer from soundcloud that the low end takes over big time. ...
- Thu Feb 26, 2015 11:00 am
- Forum: Mixcraft
- Topic: MP3 Mixdown always has way too much low end....Help!
- Replies: 17
- Views: 8188
Re: MP3 Mixdown always has way too much low end....Help!
??? That's what I did (Previous post below) Originally master track was 4800 rate and 32 Bit depth but the mix down to MP3 was at 44100 rate....16 Bit depth. So I did the following.. 1. Changed the mix down to WAV instead of MP3 2. Changed the device preferences to 48000 rate / 32 Bit. 3. Brought ba...
- Sun Feb 22, 2015 11:21 am
- Forum: Mixcraft
- Topic: MP3 Mixdown always has way too much low end....Help!
- Replies: 17
- Views: 8188
Re: MP3 Mixdown always has way too much low end....Help!
Hi, Look at your sample rate in sound device preferences, then mix down to a wav file that has the same sample rate. Click Edit Details when you go to mix down to set the sample rate of the wav file. Greg Ok, Did that. Originally master track was 4800 rate and 32 Bit depth but the mix down to MP3 w...
- Fri Feb 20, 2015 7:11 pm
- Forum: Mixcraft
- Topic: MP3 Mixdown always has way too much low end....Help!
- Replies: 17
- Views: 8188
Re: MP3 Mixdown always has way too much low end....Help!
Ok, so I watched a tutorial on YouTube using Isotope to master the track. The master sounds a lot better in Mixcraft. I mixdown to a wav file and upload to soundcloud. Same thing. It didn't sound any different. It's almost like the mixed down file wasn't the master. Am I missing a step?
- Fri Feb 20, 2015 11:27 am
- Forum: Mixcraft
- Topic: MP3 Mixdown always has way too much low end....Help!
- Replies: 17
- Views: 8188
MP3 Mixdown always has way too much low end....Help!
Whenever I mix down to MP3 the low end/bass is WAY too pronounced.....yet the mix in MC 7 sounds great. Any suggestions to what I'm doing/not doing? None of the tracks red line pre-mixdown....Thanks ahead of time for any help
- Tue Feb 17, 2015 8:22 am
- Forum: Mixcraft
- Topic: Rendered Video out of sync with audio track
- Replies: 2
- Views: 1615
Re: Rendered Video out of sync with audio track
Thanks for the reply Eric. By sample rate do you mean frames per second?